Super Mario Kart
por P-atix en Printables
Super Mario Kart
Licencia
Solo uso personalCC BY-NC-ND 4.0 — Atribución, no comercial, sin derivadas
Solo para uso personal, sin modificarlo y dando crédito. No se permite vender ni redistribuir cambios.
Al descargar aceptas respetar la licencia y dar crédito a P-atix.
Archivos (31)
- 01_rear wheel 2X.STL STL · 668 KB
- 02_front wheel 2X.STL STL · 668 KB
- 03_wheel trim 4X.STL STL · 469 KB
- 04_rear wheel pin 2X.STL STL · 269 KB
- 05_wheel arm 2X.STL STL · 389 KB
- 06_wheel axle 1X.STL STL · 283 KB
- 07_wheel spacer 4X.STL STL · 281 KB
- 08_dowel pin 5X.STL STL · 176 KB
- 09_front wheel pin 2X.STL STL · 246 KB
- 10_chassis A 1X - LOGO.STL STL · 579 KB
- 11_chassis B 1X.STL STL · 637 KB
- 12_chassis seat 1X.STL STL · 7,6 MB
- 13_bonnet no logo 1X.STL STL · 1,5 MB
- 14_steering arm 1X.STL STL · 351 KB
- 15_steering wheel 1X.STL STL · 290 KB
- 16_fender left 1X.stl STL · 123 KB
- 17_fender right 1X.STL STL · 123 KB
- 18_engine block 1X.STL STL · 1,4 MB
- 19_exhaust pipe version A 1X.STL STL · 5,4 MB
- 22_bonnet with M logo 1X.STL STL · 1,6 MB
- 23_M logo.STL STL · 108 KB
- 01_wheels_0.3mm_PETG_MK3S_1h5m.gcode GCODE · 3,8 MB
- 02_wheel trim_0.2mm_PETG_MK3S_33m.gcode GCODE · 1,8 MB
- 03_pin_0.2mm_PETG_MK3S_1h4m.gcode GCODE · 5,0 MB
- 04_wheel arm_0.2mm_PETG_MK3S_1h13m.gcode GCODE · 3,2 MB
- 05_chassis seat_0.3mm_PETG_MK3S_2h13m.gcode GCODE · 5,9 MB
- 06_fender_0.3mm_PETG_MK3S_31m.gcode GCODE · 822 KB
- 07_chassis B_0.3mm_PETG_MK3S_1h56m.gcode GCODE · 2,6 MB
- 08_chassis A 1X - LOGO_0.3mm_PETG_MK3S_1h46m.gcode GCODE · 2,3 MB
- 09_M logo_0.2mm_PETG_MK3S_7m.gcode GCODE · 137 KB
- Super Mario Kart - assembly.pdf PDF · 1,5 MB
- Categoría
- Juguetes y juegos
- Formatos
- STL, GCODE, PDF
- Descargas
- 3,818
- Publicado
Sobre este modelo
Super Mario Kart inspired toy with movable wheels and steering. I hate supports so all parts designed to be printed without supports. All tolerances are checked for easy assemble. Make sure your printer is calibrated. Every printer is not the same i guess. If some part wont fit try change resolution of model +/- one percent. Original look required four colors (white,red,blue,black) But it's not necessary to be printed in these colors use any color you want. For build check assemble.pdf
Printer setup: Nozzle diameter 0,4 Layer height 0.20 / 0.30mm 15-20% infill No supports
Descripción original del autor, publicada en Printables.
