Mini Barrel Cooper's Puzzle Box
Small but devious!
Thangs entrega los archivos a usuarios con cuenta gratuita
Licencia
Uso comercial permitidoPuedes imprimirlo, modificarlo y venderlo dando crédito al autor.
Al descargar aceptas respetar la licencia y dar crédito a 3D P.
Archivos (24)
- Assembled.3mf 3MF · 1,4 MB
- OPTIONAL_Cork_For_DK_Logo.stl STL · 241 KB
- OPTIONAL_DK_Logo.stl STL · 258 KB
- Stand_Front.stl STL · 35 KB
- Stand_Side.stl STL · 3 KB
- Top_Shell_-_M5.stl STL · 2,0 MB
- Bottom_Shell_-_M3.stl STL · 1,9 MB
- Bottom_Shell_-_M4.stl STL · 1,9 MB
- Bottom_Shell_-_M5.stl STL · 1,9 MB
- Cork.stl STL · 234 KB
- Middle_Shell_-_M3.stl STL · 982 KB
- Middle_Shell_-_M4.stl STL · 986 KB
- Middle_Shell_-_M5.stl STL · 984 KB
- Screw.stl STL · 1,9 MB
- Top_Shell_-_M3.stl STL · 2,0 MB
- Top_Shell_-_M4.stl STL · 2,0 MB
- Top_Shell.stl STL · 2,0 MB
- Bottom_Lid.stl STL · 159 KB
- Bottom_Shell.stl STL · 1,9 MB
- Large_Hoop.stl STL · 903 KB
- Middle_Shell.stl STL · 986 KB
- Small_Hoop.stl STL · 900 KB
- Solved_Plaque.stl STL · 134 KB
- Top_Lid.stl STL · 204 KB
- Categoría
- Juguetes y juegos
- Formatos
- 3MF, STL
- Descargas
- 168
- Publicado
Sobre este modelo
Small but devious!
This 2/3 scale version of The Barrel Cooper's Puzzle Box (https://thangs.com/mythangs/file/23218) includes all the tricks of the original with a few more twists!
Introduction https://youtu.be/URUGXzpI2-I
New Stuff! - Removes the "snap to position" spots. Solvers will need to work harder to logic out the correct rotation points. The puzzle still hints at these with visual indicators for those looking closely. - Removing the cork now requires an additional step. - Fewer parts to print! - Less hardware to assemble!
Hardware
The mini version of this puzzle uses less hardware than the original! It can also support a wider range of bolt sizes.
Requered
One of the following bolt options:
M3 x 50mm Bolt & M3 locknut M4 x 50mm Bolt & M4 locknut M5 x 50mm Bolt & M5 locknut
You can also try bolts as short as 40mm, but that does not leave much room for the locknut.
Recommended
Add magnetic latch to hold cork (adds an additional puzzle step)
One 3mm x 3mm Cylinder Magnet One 4mm 12 mm Steel Dowel Pin O-rings or very thin rubber bands to make parts stick in place more firmly
Can I sell copies of this? Yes! This project was shared under the Creative Commons - Attribution (https://creativecommons.org/licenses/by/4.0/) license.
This license allows selling copies, but you must provide proper attribution, as detailed in the license itself.
Please note that any other projects linked here (remixes or related projects) may have a different license. Please respect those licenses.
This license applies only to the model files (STL, 3MF, STEP, F3D) included in this project. It does not apply to photos, videos, my logo, or other supplemental graphics attached to or displayed with this project.
Click here for attribution examples (https://wiki.creativecommons.org/wiki/best_practices_for_attribution)
Descripción original del autor, publicada en Thangs.
