Fidget Square

The "Keeps Your Hands Busy" Fidget Square 🔲

A fidget toy for your desk. It sits flat as a square plate, and every way you move the stem gives it a different look.

🟩 𝗪𝗔𝗬𝗦 𝗧𝗢 𝗣𝗟𝗔𝗬

▸ 𝗧𝘄𝗶𝘀𝘁 𝘁𝗵𝗲 𝗦𝘁𝗲𝗺 — Leave it flat on the desk and twist. The 19 rings sweep around into a pinwheel, and every ring turns until its corners meet the ring outside it.

▸ 𝗣𝘂𝘀𝗵 𝗮𝗻𝗱 𝗣𝘂𝗹𝗹 — Slide the stem from side to side and the rings shift off-center for a whole different set of visuals.

▸ 𝗟𝗶𝗳𝘁 𝗜𝘁 𝗨𝗽 — Raise it by the stem and the rings step down into a pyramid.

▸ 𝗛𝗲𝗮𝗿 𝗜𝘁 𝗦𝗲𝘁𝘁𝗹𝗲 — Raise and lower it on the desk and it makes a satisfying sound as the rings come back down.

▸ 𝗧𝗲𝘅𝘁𝘂𝗿𝗲𝗱 𝗦𝘁𝗲𝗺 — The stem is textured, so it has a tactile feel under your fingers while you fidget.

🟩 𝗪𝗛𝗔𝗧 𝗠𝗔𝗞𝗘𝗦 𝗜𝗧 𝗪𝗢𝗥𝗞

▸ 𝗣𝗿𝗶𝗻𝘁𝘀 𝗶𝗻 𝗣𝗹𝗮𝗰𝗲 — One print, no assembly. All 19 rings and the stem come off the plate already captured inside each other.

▸ 𝗘𝘃𝗲𝗻 𝗚𝗮𝗽, 𝗔𝗹𝗹 𝘁𝗵𝗲 𝗪𝗮𝘆 𝗢𝘂𝘁 — Every ring sits the same distance from the next at every height, so each one turns freely instead of binding up.

▸ 𝗢𝗻𝗲 𝗖𝗼𝗹𝗼𝗿, 𝗡𝗼 𝗦𝘄𝗮𝗽𝘀 — A single spool, no filament changes, no purge and no prime tower.

🟩 𝗖𝗛𝗘𝗖𝗞 𝗬𝗢𝗨𝗥 𝗕𝗘𝗗 𝗙𝗜𝗥𝗦𝗧

▸ 126 x 126mm and 39mm tall with the stem. It fits a 150mm bed, so it prints on almost anything.

🟩 𝗣𝗥𝗜𝗡𝗧 𝗦𝗘𝗧𝗧𝗜𝗡𝗚𝗦

No supports required · no brim · 0.20mm layer height · 2 walls · 10% grid infill · PLA

Printed on a Creality Hi 1 in 2h 32m and 69g. Happy fidgeting! 🔲