Big-Iron dart blaster
por Autistic_meerkat en Printables
Big-Iron is a single action revoler that shoots half length nerf darts
Licencia
Solo uso personalCC BY-NC-SA 4.0 — Atribución, no comercial, compartir igual
Uso personal dando crédito; sin fines comerciales y las modificaciones con la misma licencia.
Al descargar aceptas respetar la licencia y dar crédito a Autistic_meerkat.
Archivos (40)
- plunger.stl STL · 39 KB
- plunger_tip.stl STL · 248 KB
- air_channel_alu.stl STL · 467 KB
- plunger_bar.stl STL · 47 KB
- PLA_air_channel_oring_13.3.stl STL · 408 KB
- TPU_air_channel_oring.stl STL · 416 KB
- arm_latch.stl STL · 14 KB
- cylinder_indexing_thing.stl STL · 60 KB
- cylinder_arm_guide_4mm.stl STL · 47 KB
- cylinder_arm.stl STL · 73 KB
- cylinder_lock.stl STL · 33 KB
- TPU_hard_cylinder_lock_latch.stl STL · 35 KB
- TPU_98A_cylinder_lock_latch.stl STL · 34 KB
- catch.stl STL · 9 KB
- hammer_L.stl STL · 179 KB
- trigger.stl STL · 170 KB
- rearsight.stl STL · 3 KB
- priming_bar.stl STL · 103 KB
- arm_latch_knob.stl STL · 277 KB
- frontsight.stl STL · 141 KB
- hand.stl STL · 35 KB
- trigger_link.stl STL · 10 KB
- barrel_clamp.stl STL · 65 KB
- cylinder_13.1mm.stl STL · 592 KB
- hammer_R.stl STL · 192 KB
- hammer_R_V2.stl STL · 191 KB
- receiver_R.stl STL · 552 KB
- receiver_R_V2.stl STL · 557 KB
- receiver_L.stl STL · 565 KB
- grip_R_logo.stl STL · 375 KB
- grip_L_logo.stl STL · 375 KB
- grip_R_plain.stl STL · 238 KB
- grip_L_plain.stl STL · 238 KB
- cover_R.stl STL · 166 KB
- cover_L.stl STL · 108 KB
- barrel_shroud.stl STL · 684 KB
- barrel_shroud_2c.stl STL · 252 KB
- name_2c.stl STL · 232 KB
- nerf_big iron.step STEP · 6,6 MB
- BIG IRON Build guide-hardware list-print guide.pdf PDF · 1,7 MB
- Categoría
- Juguetes y juegos
- Formatos
- STL, STEP, PDF
- Descargas
- 1,802
- Publicado
Sobre este modelo
Big-Iron is a hammer primed nerf revolver, with swappable six shot cylinders.
Before starting this build, i recommend reading the PDF file with the build guide and hardware list first. There are a few tricky steps in the assembly, so its probably not something i would recommend as a first build. There are two versions for the plunger. One with a aluminum plunger tube and one that uses internals from the x-shot micro2.0.
Information about performance and everything else is in the PDF as well.
Change log:
9/25/2026: Added file "receiver_R_V2" and "Hammer_R_V2" both parts need one more brass insert each. Updated Build guide/hardware list.
Descripción original del autor, publicada en Printables.
