Wyze Pan Cam K2 Plus Riser Mount

Wyze Pan Cam Mount for the D3P K2 Plus Riser — Camera Over the Bed 🎯

I run a D3P riser on my Creality K2 Plus, and I wanted a Wyze Pan Cam watching the bed from the top, without blocking any of the riser's vents. So I designed this mount. It slides onto the front of the riser, holds the camera with one screw, and keeps the cable tucked inside.

🟩 𝗪𝗛𝗔𝗧 𝗬𝗢𝗨 𝗡𝗘𝗘𝗗

▸ 𝗧𝗵𝗲 𝗗𝟯𝗣 𝗥𝗶𝘀𝗲𝗿 𝗳𝗼𝗿 𝗖𝗿𝗲𝗮𝗹𝗶𝘁𝘆 𝗞𝟮 𝗣𝗹𝘂𝘀 — Designed by Darren 3d Print. This mount is built to fit his K2 Plus riser. His riser for the plain K2 is a different size. https://thangs.com/designer/Darren%203d%20Print/3d-model/D3P%20Riser%20for%20Creality%20K2%20Plus-1411469

▸ 𝗔 𝗪𝘆𝘇𝗲 𝗣𝗮𝗻 𝗖𝗮𝗺 𝘃𝟰 — The camera I designed it around and use on mine. Other pan cams may work too, as long as they have a 1/4-20 mount.

▸ 𝗢𝗻𝗲 𝟭/𝟰-𝟮𝟬 𝘀𝗰𝗿𝗲𝘄, 𝟯/𝟰" 𝗹𝗼𝗻𝗴 — Any head style works. I used a brass thumb screw, so no tools are needed.

🟩 𝗪𝗛𝗔𝗧 𝗠𝗔𝗞𝗘𝗦 𝗜𝗧 𝗪𝗢𝗥𝗞

▸ 𝗦𝗹𝗶𝗱𝗲𝘀 𝗢𝗻𝘁𝗼 𝘁𝗵𝗲 𝗥𝗶𝘀𝗲𝗿 — No glue, and no screws into the printer or the riser.

▸ 𝗖𝗹𝗶𝗽-𝗜𝗻 𝗥𝗲𝘁𝗮𝗶𝗻𝗶𝗻𝗴 𝗕𝘂𝗹𝗯𝘀 — Round bulbs clip in once the mount is slid into place. Without them, printer vibration would slowly walk the mount out. With them, it stays put.

▸ 𝗟𝗲𝗮𝘃𝗲𝘀 𝗘𝘃𝗲𝗿𝘆 𝗩𝗲𝗻𝘁 𝗢𝗽𝗲𝗻 — It was designed to cover none of the riser's air vents.

▸ 𝗖𝗮𝗯𝗹𝗲 𝗥𝘂𝗻𝘀 𝗜𝗻𝘀𝗶𝗱𝗲 — The camera cable runs inside the mount, out a hole in the back, and into the riser's inside track.

🟩 ONE TRADEOFF: THE TOP GLASS

With the camera in place, the riser's top glass can't go on. I don't need the glass for PLA or PETG, so I set mine aside. For materials that need a closed chamber, like ABS or ASA, take the camera off and put the glass back.

🟩 𝗪𝗛𝗬 𝗣𝗘𝗧𝗚

I printed it in PETG on purpose. It flexes enough for the retaining bulbs to clip in, and it is strong enough to hold up the camera.

🟩 𝗣𝗥𝗜𝗡𝗧 𝗦𝗘𝗧𝗧𝗜𝗡𝗚𝗦

One plate, already set up in the 3MF:

▸ 1 h 49 m and 78 g. Prints flat, with no supports and no brim.

0.20mm layer height · 2 walls · 10% gyroid · 5 top and 3 bottom shells · Z anti-aliasing · PETG · 250 °C nozzle · 70 °C Textured PEI plate · sliced on a Creality K2 Plus with a 0.4mm nozzle

🟩 𝗧𝗛𝗘 𝗡𝗨𝗠𝗕𝗘𝗥𝗦

▸ Size: 165 x 82 x 50mm

▸ Hardware: one 1/4-20 x 3/4" screw

▸ Material: PETG

▸ Fits: the D3P riser for the Creality K2 Plus

Designed for my K2 Plus, and printed on it. Happy printing! 🎯