WMP MP5K - Wiimote & Prop Versions plus Stock DLC
por Adam Freeman en MyMiniFactory
ok, so first up, this was originally two releases on my Patreon which I have just smashed together into one.
MyMiniFactory entrega los archivos a usuarios con cuenta gratuita
Licencia
Solo uso personalCC BY-NC-SA 4.0 — Atribución, no comercial, compartir igual
Uso personal dando crédito; sin fines comerciales y las modificaciones con la misma licencia.
Al descargar aceptas respetar la licencia y dar crédito a Adam Freeman.
Archivos (33)
- bolt01.stl STL
- bolt02.stl STL
- bolt03.stl STL
- mag_C1.stl STL
- mag_C2.stl STL
- mag_S1.stl STL
- mag_S2.stl STL
- prop_BodyLeft.stl STL
- prop_BodyRight.stl STL
- prop_NoGrip.stl STL
- prop_Top.stl STL
- prop_trigger.stl STL
- prop_WithGrip.stl STL
- Ring_Left.stl STL
- Ring_Right.stl STL
- ring.stl STL
- S1_Back.stl STL
- S1_Bolt.stl STL
- S1_Left.stl STL
- S1_Right.stl STL
- S2_Back.stl STL
- S2_Left.stl STL
- S2_Right.stl STL
- S3_HingeParts.stl STL
- S3_StockA.stl STL
- S3_StockB.stl STL
- wmp_BodyLeft.stl STL
- wmp_BodyRight.stl STL
- wmp_nogrip.stl STL
- wmp_trigger.stl STL
- wmp_withgrip.stl STL
- wmp_withNC.stl STL
- wmp_WM_Holder.stl STL
- Categoría
- Cosplay y props
- Formatos
- STL
- Descargas
- 5
- Publicado
Sobre este modelo
ok, so first up, this was originally two releases on my Patreon which I have just smashed together into one. I have removed duplicates and any files (like the original body parts) that had updated versions included in the Stock DLC. ...
Here is a wiimote version and prop version of the well known MP5K.
There are front grip, no front grip and nunchuk variations on the lower front section. Also four mags to choose from shared with the wmp5 sd2 I did a while back.
I printed mine with a 5% Rectilinear infill with basic pla. You might want a brim on the bolts & mags, plus there are a couple of cantilever overhangs that need supporting: wmp_wmholder (the lower, back corner edge), prop_nogrip & prop_withgrip (the front corners). I try not to rely on supports but I thought it was a shame to disrupt the visual lines of the design, by changing angles to remove them. If you don't want your slicer getting happy with supports everywhere then use the (manual supports) paint option and highlight the underside (and outer edge) of the overhangs.
...
And also included here is the Stock DLC:
Ring = This just allows you to have no stock and fit the strap ring on like the original.
S1 = Is the stock from the MP5 SD2, modified to fit. S2 = Is a telescopic stock, ~220 to ~346mm in length. S3 = Is a hinged stock with two alternatives StockA (~214mm) StockB (~164mm)
The S3 hinged stocks swing around to the left, if you want it to swing around to the right, mirror all the S3 parts (3 parts, bolt & StockA/B) in your slicer (Mirror - Y axis)
Please act now! Stocks are limited...
--PATREON & PATREON SHOP. --https://www.patreon.com/3DFreeman
Thanks for your continued support!
Descripción original del autor, publicada en MyMiniFactory.
