Victorinox Swiss Army Knife 91 mm scales
por Lorenzo en Printables
Replacement scales/covers for Swiss Army Knife 91mm
Licencia
Solo uso personalCC BY-NC 4.0 — Atribución, no comercial
Puedes imprimirlo y modificarlo para uso personal dando crédito. No se permite vender las impresiones.
Al descargar aceptas respetar la licencia y dar crédito a Lorenzo.
Archivos (27)
- Swiss Army Knife Scales.step STEP · 560 KB
- Swiss Army Knife Scales.f3d F3D · 645 KB
- BottomScale_Fillet.stl STL · 2,0 MB
- BottomScale_Fillet_Solid.stl STL · 1,6 MB
- BottomScale_Fillet_NoToothpickSlot.stl STL · 2,0 MB
- BottomScale_Fillet_Solid_NoToothpickSlot.stl STL · 1,6 MB
- BottomScale_Chamfer.stl STL · 2,4 MB
- BottomScale_Chamfer_Solid.stl STL · 2,0 MB
- BottomScale_Chamfer_NoToothpickSlot.stl STL · 2,4 MB
- BottomScale_Chamfer_Solid_NoToothpickSlot.stl STL · 2,0 MB
- TopScale_Fillet_Cross.stl STL · 2,4 MB
- TopScale_Fillet_Cross_Solid.stl STL · 2,0 MB
- TopScale_Fillet_Cross_NoTweezersSlot.stl STL · 2,4 MB
- TopScale_Fillet_Cross_Solid_NoTweezersSlot.stl STL · 2,0 MB
- TopScale_Chamfer_Cross.stl STL · 3,0 MB
- TopScale_Chamfer_Cross_Solid.stl STL · 2,5 MB
- TopScale_Chamfer_Cross_NoTweezersSlot.stl STL · 3,0 MB
- TopScale_Chamfer_Cross_Solid_NoTweezersSlot.stl STL · 2,6 MB
- TopScale_Fillet.stl STL · 2,2 MB
- TopScale_Fillet_Solid.stl STL · 1,7 MB
- TopScale_Fillet_NoTweezersSlot.stl STL · 2,2 MB
- TopScale_Fillet_Solid_NoTweezersSlot.stl STL · 1,8 MB
- TopScale_Chamfer.stl STL · 2,7 MB
- TopScale_Chamfer_Solid.stl STL · 2,3 MB
- TopScale_Chamfer_NoTweezersSlot.stl STL · 2,7 MB
- TopScale_Chamfer_Solid_NoTweezersSlot.stl STL · 2,3 MB
- CrossLogo.stl STL · 565 KB
- Categoría
- Herramientas
- Formatos
- STEP, F3D, STL
- Descargas
- 1,810
- Publicado
Sobre este modelo
Replacement scales for Victorinox Swiss Army knife 91 mm. In the files section there are a few different variants, in particular with and without the slot for the toothpick and tweezers and with and without the Victorinox cross logo; as well as the .step and fusion 360 files. I also included a version with a chamfer instead of the round fillet. Print settings I printed at 0.15 mm layer height with 3 perimeters, 5 bottom/top layers, and 20% gyroid infill; but any settings should be good. You can print on both sides based on how you prefer the top finish. If you print with the top up (so that the rivets' slot faces the bed) you might need to increase the tolerances to compensate for the bridges. If the tolerances are too high or too low for your printer you can easily adjust them in the fusion 360 files by changing the parameters Tolerance and PinTolerance.
Descripción original del autor, publicada en Printables.
