The Fifth Element Stones (Elemental Stones)
por Phillip Avery en Thingiverse
UPDATE 5/18: "Fire_Stone_2018" and "WInd_Stone_2018 have been added. I removed the original versions as well as the earlier repaired versions and replaced them with the 2018 versions. All cut versions are still from the original files so if you are having problems printing cut or grouped versions...
Licencia
Solo uso personalCC BY-NC-ND 4.0 — Atribución, no comercial, sin derivadas
Solo para uso personal, sin modificarlo y dando crédito. No se permite vender ni redistribuir cambios.
Al descargar aceptas respetar la licencia y dar crédito a Phillip Avery.
Archivos (20)
- Fire_Stone_2018.stl STL · 19,8 MB
- Wind_Stone_2018.stl STL · 19,6 MB
- Earth_Stone.stl STL · 2,8 MB
- Earth_Stone_fixed.stl STL · 3,4 MB
- Water_Stone.stl STL · 3,0 MB
- Fire_Stone_Cut_4_Prnt.stl STL · 5,2 MB
- Fire_Stone_Cut_4_Prnt.x3g X3G · 43,7 MB
- Elemental_Stone_Light_Cover.stl STL · 4 KB
- Earth_Stone_Btm.stl STL · 1,4 MB
- Fire_Stone_Top.stl STL · 4,6 MB
- Water_Stone_GRP.stl STL · 3,5 MB
- Earth_Stone_GRP.stl STL · 3,4 MB
- Wind_Stone_Btm.stl STL · 2,6 MB
- Fire_Stone_GRP.stl STL · 5,3 MB
- Water_Stone_Btm.stl STL · 1,1 MB
- Earth_Stone_Top.stl STL · 2,0 MB
- Water_Stone_Top.stl STL · 2,4 MB
- Wind_Stone_GRP.stl STL · 5,8 MB
- Fire_Stone_Btm.stl STL · 700 KB
- Wind_Stone_Top.stl STL · 3,2 MB
- Categoría
- Cosplay y props
- Formatos
- STL, X3G
- Descargas
- 74,904
- Publicado
Sobre este modelo
UPDATE 5/18: "Fire_Stone_2018" and "WInd_Stone_2018 have been added. I removed the original versions as well as the earlier repaired versions and replaced them with the 2018 versions. All cut versions are still from the original files so if you are having problems printing cut or grouped versions download the 2018 files and re-cut them for your needs. "UPDATE 8/17: Cut all stones in half for smaller printers. Also added a "GRP" file of each stone which is the two halves positioned on the build plate in the orientation that I printed mine. Support may be needed for some printers. I printed mine without support. UPDATE: 12/16, Some people were having trouble with slicing the original "Fire Stone" so I added some new versions of that stone. I added the full stone repaired, a cut version oriented the way I printed them and then a sliced file of the cut version sliced with the Makerbot software. So now you have some options. This is my version of the Elemental Stones from the movie The Fifth Element. They are 1 to 1 scale and were built in TinkerCad based on very good photos of the movie props. I did my best to make these as accurate as possible. The "damage/cracks" were drawn and placed as closely as possible to where they appeared on the photos of the props. I made the stones hollow to aid in printing and I leave it up to you to cut them as you need to fit your own printers. 1 stone cut in half took 11.5 hours to print on my Mbot clone. Be sure to check out my other Fifth Element props on this site. I have also included an Elemental Stone Light Cover file. This file is designed to set ontop any of the stones. I suggest either printing it in a translucent filament or printing it then making a mold and casting in translucent colors to match the type of stone you place it on. For added drama you could use some of Smooth-On's Cast Magic powder in a tinted resin to get the sparkle effect as seen in the movie. DO NOT place candles under this cover only light them with low temp LED lights or battery powered flicker candles. The light cover is not vented and will melt if you use anything else to light them.
Descripción original del autor, publicada en Thingiverse.
