Sovol / Comgrow Dual SH02 / SH03 Stand w/ Drawers

Hey all, so I posted a shorter riser for the Sovol / Comgrow SH03 and received a great idea from a comment… Drawers! So simple and thank you for the idea! I also realized that 2 SH02 dryers had the same rough dimensions of the single SH03, so if this peaks your interest, please read on!

I took my original design I made for a shorter height need on my SH03 (https://makerworld.com/en/models/3052593-no-hardware-sovol-comgrow-sh03-dryer-riser-stand) to another level (literally, a 60mm another level…) and realized that I have a set up that requires the dryer to be “horizontal” and another that requires the dryer to be “vertical”.

In making this, I realized that one set of drawers would not do! I raised the original model to a height of 100mm and added several sets of drawers to match how you may want to orient the dryer to your printer.

BONUS!!!: I use 2 Sovol / Comgrow SH02 dryers in one of my set ups and one where I have an SH03 horizontal and this fits and works as a dryer for 2 SH02 (See picture with green and black stand) or one SH03 (See Picture with blue stand and gray drawers).

Extra Bonus and Brownie Points For Helping Me With Brain Fog: If you use a single or dual SH02 setup, please let me know if I should work on something on one side for a single SH02 dryer (drawer, cubby, etc…) that will take the extra space and I will see what I can do!

Stand Notes:

- ***YOU WILL NEED A PRINTER CAPABLE OF 256mm IN ONE DIMENSION AT A MINIMUM, THE STAND IS 250MM LONG PER SIDE.***

- For the stand, it still prints in 2 parts and uses nearly the whole 256 mm plate dimension per side, so PLEASE use brims and glue if you can. Mine warped slightly and it did not impact ability to be used, but due to the size, glue and brims are strongly recommended! This baby wants to warp like mad!

- As mentioned above, the stand prints in 2 parts, left and right and slides together with dovetails. No need to glue.

- Note that the extended lip is to the front of the dryer, and the hole on the right lines up to the hole that opens during drying.

Drawer Notes:

- The drawers just slide under the base, no need to glue or anything.

- In the drawer files: - L= Left, R= Right, F= Front and B=Back (all based on how you face opening the dryer, where the lip of the stand is the front).

- Drawers will be specific to orientation, so please pay attention to how you want to orient this for your work space: - The print files that are labeled “SH03 Front Drawers” are for if you have the dryer oriented to where you open the dryer head on (see green base and black drawers in the pictures).

- “SH03 Side Drawers” is if you open it from the side (duy…?!). The blue and gray drawer set shows a side orientation on the left. If you only need the left side, download and print those 2 drawers labeled “LF” and “LB”, but if you need right print “RF” and RB".

- If you print the “SH03 Side Drawer File” all 4 drawers can be printed and used if you can and want to access them.

- If you print the front drawer version, please note, that you may want to enable supports on the handle if you print in PETG. It may sag as the top is a bit wide and some slicers slow down too much for this far of an overhang.

- PLA may sag as well on the handle, so it may just be a good idea to use tree supports, but if you are like me and feel lucky, let it roll and see what happens! - With proper tuning on PETG, mine printed fine, but I did get feedback that others have sag, so please use supports.

- PETG worked just fine for sag on the side drawers, but again, use your best judgement and if in doubt, trust tree supports.

- ***The stand will not work with all 6 drawers, but feel free to print them all and use them for storage or as a way to justify another dryer… I wont judge…***

Print Settings:

- Drawers: - Material: PETG or PLA - If PETG, supports may be needed to address possible sag in handle, please use tree supports if in doubt.

- If using PLA, I was able to print both sets without supports, but please add if you want extra security.

- Walls: 2

- Infill: 8%

- Bottom/Top Layers: 3 Each

- Supports: See notes above, but if in doubt, use trees

- Stand: - Material: PETG (PLA May Be OK, But Weight and Heat May Warrant PETG)

- Walls: 3

- Infill: 10% rectilinear