Printy Pipes - Construction Toy
This construction toy is inspired by the discontinued Pipeworks sets from the 1980s.
Thangs entrega los archivos a usuarios con cuenta gratuita
Licencia
Solo uso personalCC BY-NC 4.0 — Atribución, no comercial
Puedes imprimirlo y modificarlo para uso personal dando crédito. No se permite vender las impresiones.
Al descargar aceptas respetar la licencia y dar crédito a 3D P.
Archivos (104)
- Set.step STEP · 5,8 MB
- Clamp Pipe Small.stl STL · 774 KB
- Clamp Pipe Medium.stl STL · 418 KB
- Clamp Pipe Large.stl STL · 437 KB
- Lock Ring.stl STL · 61 KB
- TPU Rivet.stl STL · 9 KB
- Pipe Large.stl STL · 357 KB
- Pipe Medium.stl STL · 352 KB
- Pipe Small.stl STL · 655 KB
- Clip Connector 2.stl STL · 738 KB
- Clip Connector 1.stl STL · 462 KB
- Hinge Connector 2.stl STL · 738 KB
- Hinge Connector 1.stl STL · 480 KB
- X Connector 1.stl STL · 985 KB
- X Connector 2.stl STL · 985 KB
- X Connector 3.stl STL · 985 KB
- X Connector 4.stl STL · 985 KB
- 4-Way Connector 4.stl STL · 1008 KB
- 4-Way Connector 3.stl STL · 946 KB
- 4-Way Connector 2.stl STL · 1,0 MB
- 4-Way Connector 1.stl STL · 1,0 MB
- T Connector 3.stl STL · 915 KB
- T Connector 1.stl STL · 985 KB
- T Connector 2.stl STL · 949 KB
- Corner Connector 3.stl STL · 836 KB
- Corner Connector 2.stl STL · 828 KB
- Corner Connector 1.stl STL · 835 KB
- L Connector 2.stl STL · 860 KB
- L Connector 1.stl STL · 884 KB
- I Connector.stl STL · 801 KB
- Clip Connector 2 Alternate.stl STL · 720 KB
- Hinge Connector 2 Alternate.stl STL · 720 KB
- Tool.stl STL · 93 KB
- 2-Way Hinge Connector 1.stl STL · 827 KB
- 2-Way Hinge Connector 2.stl STL · 738 KB
- 3-Way Hinge Connector 1.stl STL · 773 KB
- 3-Way Hinge Connector 2.stl STL · 738 KB
- 4-Way Hinge Connector 1.stl STL · 730 KB
- 4-Way Hinge Connector 2.stl STL · 738 KB
- 5-Way Connector 1.stl STL · 1009 KB
- 5-Way Connector 2.stl STL · 1,0 MB
- 5-Way Connector 3.stl STL · 1,0 MB
- 5-Way Connector 4.stl STL · 1,0 MB
- 5-Way Connector 5.stl STL · 1,0 MB
- 6-Way Connector 1.stl STL · 1009 KB
- 6-Way Connector 2.stl STL · 1007 KB
- 6-Way Connector 3.stl STL · 1007 KB
- 6-Way Connector 4.stl STL · 1007 KB
- 6-Way Connector 5.stl STL · 1007 KB
- 6-Way Connector 6.stl STL · 1009 KB
- Curved Pipe Large 1.stl STL · 843 KB
- Curved Pipe Large 2.stl STL · 851 KB
- Curved Pipe Medium 1.stl STL · 953 KB
- Curved Pipe Medium 2.stl STL · 966 KB
- Curved Pipe Small 1.stl STL · 1,1 MB
- Curved Pipe Small 2.stl STL · 1,2 MB
- Lock Detent 1.stl STL · 34 KB
- Lock Detent 2.stl STL · 35 KB
- Lock Detent Stiff 1.stl STL · 33 KB
- Lock Detent Stiff 2.stl STL · 34 KB
- Categoría
- Educación
- Formatos
- STEP, STL
- Descargas (todas las plataformas)
- 489
- Publicado
También en
Sobre este modelo
This construction toy is inspired by the discontinued Pipeworks sets from the 1980s.
Rather that replicate the original set exactly, this has been scaled down and optimized for 3D printing. This project also includes completely new parts!
Videos - Introduction (https://youtu.be/pBeEYad1epU) - Update! (https://youtu.be/cURVq72HxiI)
Printing
This design requires no supports.
Some taller pieces may need a generous brim, especially if using a printer with a moving bed.
Look out for elephants foot (squishing on the bottom layers). This may cause tight fitting parts to fall too far out of spec. If needed, use a deburring tool to clean up the bottom edge of the prints.
Infill can be relatively low - 10-15%
Print the optional rivets in TPU or similar flexible filament.
Print the optional lock rings in PETG or strong formulations of PLA (PLA+).
Avoid using brittle PLA filaments for this project.
This design includes parts that are intended to slide and lock together with only 0.125mm of clearance. If you are unsure if your printer can reproduce this accurately, print one part of any of the joint pieces and the smallest pipe as a test. The parts should slide together without extreme force.
Assembly
This project relies heavily on glue to assemble the joint pieces. For this project, I recommend using 3D Gloop! (https://www.3dgloop.com/), which will quickly fuse the parts together.
All joints parts include alignment geometry where they connect with each other. Test positioning these parts before gluing them.
Misc
For easier organization, some identical parts have been listed multiple times. For example, the “X Joint” uses a part identical to the “T Joint”.
Can I sell copies of this?
Sorry, but no. This design is based on an existing (although discontinued) toy, so it is not available under a commercial license. Some remixes of this project may be listed under a different license.
This license applies only to the model files (STL, 3MF, STEP, F3D) included in this project. It does not apply to photos, videos, my logo, or other supplemental graphics attached to or displayed with this project.
Updates - Curved Pipes - Round Endcap - 5-Way Connector - 6-Way Connector - Multi-hinge - Slats - Detents - Tool
Descripción original del autor, publicada en Thangs.
