P51D - Mustang RC Plane
por RADdesign en Printables
This a 3D printed remote control model of the iconic P-51D Mustang from WWII.
Licencia
Solo uso personalCC BY-NC-SA 4.0 — Atribución, no comercial, compartir igual
Uso personal dando crédito; sin fines comerciales y las modificaciones con la misma licencia.
Al descargar aceptas respetar la licencia y dar crédito a RADdesign.
Archivos (49)
- F3 - FUSE Motor Shim.stl STL · 88 KB
- F3 - FUSE Motor Shim.3mf 3MF · 128 KB
- F1 - FUSE Front.3mf 3MF · 1,3 MB
- F2 - FUSE Motor Mount.3mf 3MF · 1,4 MB
- F5 - Cockpit.stl STL · 2,3 MB
- F1 - FUSE Front.stl STL · 2,4 MB
- F2 - FUSE Motor Mount.stl STL · 2,5 MB
- F5 - Cockpit.3mf 3MF · 1,2 MB
- F4 - FUSE Center.3mf 3MF · 2,7 MB
- F6 - FUSE Rear.3mf 3MF · 2,7 MB
- F4 - FUSE Center.stl STL · 5,0 MB
- F6 - FUSE Rear.stl STL · 5,2 MB
- S2 - Spinner Base.3mf 3MF · 715 KB
- S2 - Spinner Base.stl STL · 1,1 MB
- S1 - Spinner Tip.3mf 3MF · 1,2 MB
- S1 - Spinner Tip.stl STL · 2,1 MB
- RW5 - Landing Gear Plug.stl STL · 91 KB
- RW2 - Outer Wing 2.stl STL · 766 KB
- RW4 - Wing Tip.stl STL · 3,1 MB
- LW2 - Outer Wing 2.stl STL · 780 KB
- LW3 - Aileron.stl STL · 1,2 MB
- RW3 - Aileron.stl STL · 1004 KB
- LW1 - Outer Wing 1.stl STL · 2,7 MB
- LW5 - Landing Gear Plug.stl STL · 91 KB
- LW4 - Wing Tip.stl STL · 3,1 MB
- RW1 - Outer Wing 1.stl STL · 5,2 MB
- LW1 - Outer Wing 1 (built in support).stl STL · 8,2 MB
- LW - Complete Wing.3mf 3MF · 7,3 MB
- RW1 - Outer Wing 1 (built in support).stl STL · 12,1 MB
- RW - Complete Wing.3mf 3MF · 9,1 MB
- HS - Elevator Spacer.stl STL · 94 KB
- LHS3 - Elevator.stl STL · 345 KB
- RHS3 - Elevator.stl STL · 359 KB
- LHS2 - HSTAB.stl STL · 607 KB
- RHS2 - HSTAB.stl STL · 607 KB
- LHS1 - HSTAB Tip.stl STL · 1,4 MB
- RHS1 - HSTAB Tip.stl STL · 1,4 MB
- HSTAB Complete.3mf 3MF · 2,6 MB
- E4 - Top Rudder.stl STL · 406 KB
- E6 - Lower Rudder.stl STL · 1,0 MB
- E2 - VSTAB LE.stl STL · 970 KB
- E5 - Center Rudder.stl STL · 707 KB
- E3 - VSTAB Tip.stl STL · 1,1 MB
- TLG Wheel.stl STL · 2,3 MB
- MLG Wheel.stl STL · 2,3 MB
- Landing Gear Wheels.3mf 3MF · 6,3 MB
- E1 - Empennage.stl STL · 2,7 MB
- Empennage Complete.3mf 3MF · 3,6 MB
- P51D Mustang Instruction Manual.pdf PDF · 55,9 MB
- Categoría
- Varios
- Formatos
- STL, 3MF, PDF
- Descargas
- 13,965
- Publicado
Sobre este modelo
This is a 3D printed model of the P-51D Mustang from WWII. It features the fin offset and the wing washout of the original P-51. The entire model can be printed without the use of supports. I printed the entire model in PLA. This model was designed to be printed on an Ender 3 sized printer. The 3mf files supplied are from CURA and should contain the settings I used for each print. Please see the instruction manual PDF for a guide to assembling this model. Dimensions: Wing Span: 68.6cm Length: 60cm Print Time: 118 hours Material: 711 grams I haven't had the chance to take this model on its maiden flight but I will make an update when I do. I will be releasing a smaller, solid model version of this plane in the future for those that do not want the remote control.
Descripción original del autor, publicada en Printables.
