OpenRC GoKart
por Christian Erazo en Printables
This is an OpenRC Project for a Go-Kart As Some friends and I decided to create an extra class for hobby driver with…
Licencia
Solo uso personalCC BY-NC-SA 4.0 — Atribución, no comercial, compartir igual
Uso personal dando crédito; sin fines comerciales y las modificaciones con la misma licencia.
Al descargar aceptas respetar la licencia y dar crédito a Christian Erazo.
Archivos (52)
- OpenRC-GoKart-Karo_V08.stl STL · 5,2 MB
- OpenRC-GoKart-KaroHinten_1.stl STL · 4,7 MB
- OpenRC-GoKart-KaroHinten_2.stl STL · 4,6 MB
- OpenRC-GoKart-KaroVorne_2.stl STL · 42 KB
- OpenRC-GoKArt-KaroVorne_v086.stl STL · 3,4 MB
- Rear Axle Holder (Left) v0.9.stl STL · 893 KB
- OpenRC-GoKart-GT2-2.stl STL · 5,4 MB
- OpenRC_Motor_Abstandsplatte.stl STL · 511 KB
- OpenRC-GoKart-GT2-1.stl STL · 4,2 MB
- OpenRC-GoKart-RearWheelAdapter_v0.9.stl STL · 446 KB
- OpenRC-GoKart-Achse-Lager-v0.9.stl STL · 630 KB
- Rear Axle Holder (Right) v0.9.stl STL · 933 KB
- Axle 4.0.stl STL · 778 KB
- OpenRC-GoKart-Rear_Axle_v0.9.stl STL · 749 KB
- grundkorper_2.stl STL · 138,6 MB
- Zündkerze.stl STL · 9,4 MB
- endtopf.stl STL · 9,5 MB
- Zylinderkopf mit Lüftung.stl STL · 11,1 MB
- Zylinder.stl STL · 52,0 MB
- Vergaser.stl STL · 119,4 MB
- Filter.stl STL · 6,9 MB
- openrc-gokart_krummer-v4.stl STL · 15,0 MB
- Zündkerzenstecker.stl STL · 24,0 MB
- halter.stl STL · 861 KB
- front-axle-v5_1.stl STL · 485 KB
- OpenRc-GoKart-Front_Lower_BOM_Left_V087.stl STL · 489 KB
- OpenRC-GoKart-Front_Upper_BOM_Left_V087.stl STL · 580 KB
- OpenRC-GoKart-Front_Upper_BOM_Right_V087.stl STL · 577 KB
- OpenRC-GoKart-Front_Lower_BOM_Right_v087.stl STL · 486 KB
- openrc-gokart-frontwheelhub.stl STL · 636 KB
- OpenRC-GoKart-Steering_Mount_Steering_Side.stl STL · 211 KB
- OpenRC-GoKart-Steering_Mount.stl STL · 162 KB
- OpenRC-GoKart-Steering_Axle.stl STL · 194 KB
- OpenRC-GoKart-Coupling-Servo.stl STL · 304 KB
- OpenRC-GoKart-11mmBlock.stl STL · 16 KB
- OpenRC-GoKart-Coupling-Steering.stl STL · 50 KB
- OpenRC-GoKart-Steering_Wheel.stl STL · 283 KB
- wheel-lock-nut-v6.stl STL · 290 KB
- OpenRC-GoKart_Chassis_ONEPIECE_085.stl STL · 2,1 MB
- OpenRC-GoKart_Chassis_Front_V085.stl STL · 1,3 MB
- OpenRC-GoKart_Chassis_Rear_V08.stl STL · 688 KB
- OpenRC-GoKart_Chassis_Batery_Holder_V087.stl STL · 1,0 MB
- OpenRC-GoKart_Chassis_Seat.stl STL · 4,5 MB
- OpenRC_GoKart_Front_Block_V085.stl STL · 317 KB
- OpenRC-GoKart-KaroHalter_Front_V08.stl STL · 283 KB
- OpenRC_GoKart_Steering_Support_Right_V08.stl STL · 167 KB
- OpenRC_GoKart_Steering_Support_Left_V08.stl STL · 167 KB
- OpenRC-GoKart-KaroHalter_Rear_Right_V08.stl STL · 405 KB
- OpenRC-GoKart-KaroHalter_Rear_Left_V08.stl STL · 445 KB
- OpenRC-GoKart-ServoMount.stl STL · 174 KB
- OpenRC-GoKart_Chassis_Left.stl STL · 131 KB
- OpenRC-GoKart_Chassis_Right.stl STL · 131 KB
- Categoría
- Varios
- Formatos
- STL
- Descargas
- 3,687
- Publicado
Sobre este modelo
This is an OpenRC Project for a Go-Kart As Some friends and I decided to create an extra class for hobby driver with self printed RC cars ... we started this project. We will try to reuse as much as possible from other projects so that it can be reused even here. (Less engineering and of course a higher reuse of components and knowledge) PartList: Screws: 4 x M3x16 lenshead 4 x M3x10 lenshead 10 x M3x12 countersunk 13 x M3x10 countersunk 30 x M3x8 countersunk Nuts 14 x M3 Bearings: 4 x 12x18x4 (Rear Achsle and Steeringrod) 4 x 8x12x3,5 (Wheels Front) There will be also a driver in the nearer future which should be able to steer and move the head to where it drives. Feel free to comment ... as already said ... this is currently under construction. This design was published to be used and printed free of charge and not to be distributed or sold for profit. (My contribution to RC Hobbyists to try and keep it as affordable as possible)
Not official but an “assemble instruction” if needed ;)
and another one ;)
Descripción original del autor, publicada en Printables.
