Kit for Removable Panels/Doors for Voron V2/Trident using Strong Snap Latch
por Victor Mateus Oliveira en Printables
Complete set os STL using modified the Voron Snap Latch to work with M3 screws from 8mm to 12mm (you can even mix then).
Licencia
Uso comercial permitidoPuedes usarlo, modificarlo y venderlo; si distribuyes versiones modificadas deben ir con la misma licencia y sus fuentes.
Al descargar aceptas respetar la licencia y dar crédito a Victor Mateus Oliveira.
Archivos (14)
- Bottom Corner Bracket - 3mm Foam Tape.f3d F3D · 223 KB
- Corner Safety Bracket Top.f3d F3D · 238 KB
- Bottom Corner Bracket - 1mm Foam Tape.f3d F3D · 226 KB
- Stronger Snap Latch 2020 - M3 Screw.f3d F3D · 1,8 MB
- Bottom Corner Bracket - 1mm Foam Tape.3mf 3MF · 55 KB
- Bottom Corner Bracket - 3mm Foam Tape.3mf 3MF · 58 KB
- Corner Safety Bracket Top.3mf 3MF · 62 KB
- Latch M3x8-12 SHCS - 3mm Foam Tape.3mf 3MF · 265 KB
- Latch M3x8-12 SHCS - 1mm Foam Tape.3mf 3MF · 269 KB
- Latch M3x8-12 SHCS - 3mm Foam Tape Smaller.stl STL · 602 KB
- Latch M3x8-12 SHCS - 1mm Foam Tape Smaller.stl STL · 603 KB
- Door Hinge MMU.stl STL · 51 KB
- OuterHingeDoor.stl STL · 299 KB
- exhaust_cover.stl STL · 935 KB
- Categoría
- Para tu impresora
- Formatos
- F3D, 3MF, STL
- Descargas
- 1,687
- Publicado
Sobre este modelo
Stronger Snap Latch with M3 Screw Because any voron builder has tons of spare M3 screws!
This repo is based in the amazing works from: - Original Snap Latch: https://github.com/VoronDesign/VoronUsers/tree/master/printer_mods/richardjm/snap-latch-2020 - Snap Latch for M2 Screws - where I take the cad to modify: https://www.printables.com/model/643837-wide-voron-panel-snap-latch-with-lip-using-m2-scre - QD Panel Mod, uses M1.6 and M2 Screws - where I take the corners to modify: https://github.com/MotorDynamicsLab/VoronQDPanelMod
Motivation M2 and M1.6 screws are very hard to find on local stores, at least where I live. And it takes a lot of screws to cover every side of a voron!! So, it would take weeks of waiting to get all thoses tiny screws. But I have tons of spare M3x8, M3x10, M3x12, SHCS and BHCS, from my voron builds. And I thing most of voron builders have it too. So I modified these designs to fit with our spare screws! I found the current designs a little weak too, to really squish and insulate the panels. Modifications made: - Support for M3 Screws. It works with either 8mm, 10mm or 12mm, both SHSC and BHSC. **You can even mix screw sizes!** - Outer Hinge with a Straight line: The orignal design uses a curve for the outer hinge sweep path. It makes all the pressure be concentrated in just a few milimeters of plastic. I changed it to have a straight line in the middle, so it distribute all the pressure in a wide area. - Stronger outer hinge - 8mm diameter instead of 5mm: I adjusted the cad to allow customize the outer hinge diameter. It allows to apply far more pressure to the panels without any plastic fadigue. - I modified the corners for QD Panel Mod to fit better. The original design didn't hold strong in the frames for me.
Print it with standard voron parts settings. Repository: https://github.com/rhapsodyv/snap-latch-2020-m3-stronger
Edit 3/jan/2024: Added exhaust cover and smaller latch options. Edit 5/Jan/2024: Added Door Hinges.
Descripción original del autor, publicada en Printables.
