DIY RC Crane
por ProfessorBoots en Printables
Are your spirits low because I have just the thing to lift them up! Enter: RC Crane
Licencia
Solo uso personalCC BY-NC-SA 4.0 — Atribución, no comercial, compartir igual
Uso personal dando crédito; sin fines comerciales y las modificaciones con la misma licencia.
Al descargar aceptas respetar la licencia y dar crédito a ProfessorBoots.
Archivos (130)
- 1.) Main Color Pt1 Booms2 and 3.stl STL · 487 KB
- 2.) Main Color pt2 Boom1 and cabs.stl STL · 558 KB
- 3.) Main Color pt3 Crane Base.stl STL · 1,0 MB
- 4.) Main Color pt4 MISC.stl STL · 1,1 MB
- 5.) Main Color pt5 Outriggers pt1.stl STL · 76,4 MB
- 6.) Secondary Color pt1 Misc Parts.stl STL · 1,5 MB
- 7.) Secondary Color pt2 Motor Restraints and steering bars.stl STL · 1,1 MB
- 8.) Secondary Color pt 3 A-Arms and Knuckles.stl STL · 2,4 MB
- 9.) Secondary Color pt4 Outer frames.stl STL · 594 KB
- 10.) Secondary Color pt5 Wheels.stl STL · 6,0 MB
- 11.) Secondary Color pt6 Bed and Swivel Lock.stl STL · 326 KB
- 12.) Secondary Color pt7 UJoints and hubs.stl STL · 3,8 MB
- 13.) Secondary Color pt8 Gears.stl STL · 2,5 MB
- 14.) Third Color pt1 Outriggers pt2.stl STL · 4,4 MB
- 15.) Third Color pt2 Inner frames and undertones.stl STL · 2,9 MB
- 16.) 12 Tires and Suspenion TPU.stl STL · 28,0 MB
- 17.) misc TPU.stl STL · 795 KB
- 1.) UJoint Rod.stl STL · 69 KB
- 2.) Axle spur gear.stl STL · 152 KB
- 3.) UJoint Center.stl STL · 59 KB
- 4.) UJoint Outter.stl STL · 32 KB
- 5.) Hub UJoint Connection.stl STL · 44 KB
- 6.) UJoint Inner.stl STL · 29 KB
- 7.) Right Steering Knuckle.stl STL · 109 KB
- 8.) Left Steering Knuckle.stl STL · 109 KB
- 9.) Wheel.stl STL · 510 KB
- 10.) Hub.stl STL · 81 KB
- 11.) Knuckle UJoint.stl STL · 57 KB
- 12.) Upper A-Arm.stl STL · 50 KB
- 13.) Lower A-Arm.stl STL · 62 KB
- 14.) Steering rod.stl STL · 37 KB
- 15.) Middle Knuckle.stl STL · 65 KB
- 16.) hub for Center Wheels.stl STL · 66 KB
- 17.) Axle Pinion Gear.stl STL · 94 KB
- 18.) Axle Gear Restraint.stl STL · 51 KB
- 19.) Axle Gear Restraint w MTR Mount.stl STL · 75 KB
- 20.) Rear Axle Gear Restraint w MTR Mount.stl STL · 79 KB
- 21.) Inner Frame Front.stl STL · 731 KB
- 22.) Inner Frame Rear.stl STL · 730 KB
- 23.) Middle A-Arm Mount.stl STL · 123 KB
- 24.) Axle Middle Gear.stl STL · 204 KB
- 25.) A-Arm Mount Double.stl STL · 130 KB
- 26.) Suspension.stl STL · 27 KB
- 27.) Steering Bar.stl STL · 50 KB
- 28.) Rear Steering Bar.stl STL · 39 KB
- 29.) Tire.stl STL · 2,3 MB
- 30.) Servo Push rod.stl STL · 87 KB
- 31.) Motor slider for outriggers.stl STL · 42 KB
- 32.) Outrigger pinion gear.stl STL · 179 KB
- 33.) Outrigger push rod.stl STL · 47 KB
- 34.) Hex Bolt Holder.stl STL · 72 KB
- 35.) Outrigger foot2.stl STL · 36 KB
- 36.) outrigger foot1.stl STL · 124 KB
- 37.) bevel 2.stl STL · 374 KB
- 38.) Bevel 1.stl STL · 379 KB
- 39.) Outrigger rail inner.stl STL · 25 KB
- 40.) Outrigger rail.stl STL · 3 KB
- 41.) Outrigger rail retainer.stl STL · 51 KB
- 42.) left outrigger extension barrel.stl STL · 19,6 MB
- 43.) Right outrigger extension barrel.stl STL · 18,5 MB
- Categoría
- Varios
- Formatos
- STL
- Descargas
- 6,123
- Publicado
Sobre este modelo
So you think you’re a big bad 3D printing wiz, huh? Well gee do I have a project for you! This project single-handedly consumed more months of my life than I care to admit. But the finished result…? Well, it’s sweet. By far the coolest thing to ever roll across my desk. If you’ve already tackled the RC Excavator and RC Skidsteer, I’d recommend giving this a shot. Just be warned: if the excavator was a level 2, this one is at least a level 6 and I tried to convey this in my build video linked below(for your viewing pleasure). Once you've printed out a few pieces and realize what a slippery slope you’ve embarked upon, consider joining the Professorboots workshop (linked below). It helps fund the development of these RC projects and provides step-by-step guides on sourcing all the parts needed to complete your own one-of-a-kind RC Crane. ProfessorBoots Workshop Pass: https://professorboots.com/products/professorboots-workshop-pass P.S. I apologize in advance for the challenge you’re about to face, but I don't apologize for the legend you're about to become!
Descripción original del autor, publicada en Printables.
