DIY Life-Size Terminator Arm Lamp
por L L en Thingiverse
First of all. Thank you nracmo (https://www.thingiverse.com/nracmo/about) for the design! I have cleaned up a couple of parts, redesigned some of them to fit my need and raised the resolution. Further more i have designed a stand for the arm. The arm is based on the second terminator movie. If you..
Licencia
Solo uso personalCC BY-NC 4.0 — Atribución, no comercial
Puedes imprimirlo y modificarlo para uso personal dando crédito. No se permite vender las impresiones.
Al descargar aceptas respetar la licencia y dar crédito a L L.
Archivos (21)
- arm_holder_up.stl STL · 1,1 MB
- stand_middle.stl STL · 325 KB
- arm_holder_down.stl STL · 1,5 MB
- finger_index_and_ring.stl STL · 2,6 MB
- arm_tube.stl STL · 3,2 MB
- stand_top.stl STL · 307 KB
- finger_washers_5_times.stl STL · 3,6 MB
- stand_bottom.stl STL · 126 KB
- arm_extra_1.stl STL · 6,6 MB
- finger_pinky.stl STL · 2,1 MB
- hand_extras.stl STL · 6,3 MB
- finger_thumb.stl STL · 2,3 MB
- hand.stl STL · 6,2 MB
- finger_middle.stl STL · 3,4 MB
- arm_extra_2.stl STL · 4,8 MB
- arm_rods.stl STL · 4,8 MB
- hand_tubes.stl STL · 10,9 MB
- arm_rods_split_2.stl STL · 1,7 MB
- arm_rods_split_1.stl STL · 3,2 MB
- hand_tubes_Split_1.STL STL · 2,3 MB
- hand_tubes_Split_2.STL STL · 8,6 MB
- Categoría
- Hogar
- Formatos
- STL
- Descargas (todas las plataformas)
- 63,417
- Publicado
También en
Sobre este modelo
First of all. Thank you nracmo (https://www.thingiverse.com/nracmo/about) for the design! I have cleaned up a couple of parts, redesigned some of them to fit my need and raised the resolution. Further more i have designed a stand for the arm. The arm is based on the second terminator movie. If you like my work feel free to tip a small amout. It would help significant. ....................................................................................................................................... Update 10.06.2018 Fixed an error in hand.stl which could result in holes on the tip of the piston for the middle finger. (Thanks 3D_ProtoPrinting -> https://www.thingiverse.com/3D_ProtoPrinting/about) ....................................................................................................................................... Update 16.06.2018 Due to some difficulties people had with the files hand_tubes.stl and arm_rods.stl. I have added split versions of the two files. If you still have problems with a tube try to lower the speed by 50% to allow the print to cool more and use a raft. (Thanks LordGrantham -> https://www.thingiverse.com/LordGrantham/about) ....................................................................................................................................... Update 11.07.2018 Check out the Tronxy X5SA Review by Nexi-Tech (https://www.thingiverse.com/Nexi-Tech/about). You can see the lamp in action in his video! ;D https://www.youtube.com/watch?v=Pq3qjdaRnuY&t=1123s
Descripción original del autor, publicada en Thingiverse.
