Cleaning Supply Box

Cleaning Supply Box — Under-Sink Caddy with a Pinned Loop Handle 🔗 Cleaning supplies under the sink tip over, roll to the back and never come out together. This box holds the whole kit upright in sized pockets and carries it room to room in one hand. I designed the pockets around the bottles and cans I actually use, then printed it in PET-G so it shrugs off drips and spills. 🟩 𝗪𝗛𝗔𝗧 𝗠𝗔𝗞𝗘𝗦 𝗜𝗧 𝗪𝗢𝗥𝗞 ▸ 𝗡𝗶𝗻𝗲 𝗦𝗶𝘇𝗲𝗱 𝗣𝗼𝗰𝗸𝗲𝘁𝘀 — Four tall pockets for full-size trigger spray bottles, a round pocket for a cleanser can, two round pockets for aerosol cans, a rectangular pocket, and a small center pocket. ▸ 𝗥𝗼𝗼𝗺𝘆 𝗟𝗼𝗼𝗽 𝗛𝗮𝗻𝗱𝗹𝗲 — A big oval opening (131.6 x 61mm) with rounded inner edges, so a full hand fits and a heavy load doesn't dig in. ▸ 𝗣𝗶𝗻𝗻𝗲𝗱, 𝗡𝗼𝘁 𝗚𝗹𝘂𝗲𝗱 — The handle's stem slides into a slot in the box and one printed pin locks it in. No hardware, no glue. ▸ 𝗣𝗘𝗧-𝗚 𝗧𝗵𝗿𝗼𝘂𝗴𝗵𝗼𝘂𝘁 — Holds up to cleaning sprays and drips better than PLA. 🟩 𝗛𝗢𝗪 𝗧𝗢 𝗔𝗦𝗦𝗘𝗠𝗕𝗟𝗘 ▸ Slide the handle's stem down into the center slot until its hole lines up with the hole in the box wall. ▸ Find the pin's seam - a faint straight ridge down one side. Turn that ridge UP, into the pointed top of the teardrop-shaped hole. ▸ Press the pin through the box wall and the handle. It slides through the box and is a snug press fit in the handle. ▸ Too tight? Scale the pin to 99.5% or sand it lightly. If the handle won't slide into its slot, scale the handle's width to 99%. 🟩 𝗣𝗥𝗜𝗡𝗧 𝗦𝗘𝗧𝗧𝗜𝗡𝗚𝗦 Two plates, both pre-configured in the 3MF files. No supports. ▸ Box: 16 h 17 m, 862 g, 280 m of filament ▸ Handle + pin: 3 h 00 m, 137 g, 45 m of filament ▸ Total: 19 h 17 m and about 1 kg of PET-G 0.20mm layer height · PET-G · 250 °C nozzle · 70 °C bed · 0.4mm nozzle · gyroid infill · back seam Box: 2 walls · 8% infill · 4/3 top and bottom · 5mm outer brim Handle: 3 walls · 15% infill · 5/5 top and bottom · Pin: 4 walls · 100% infill The box is 320 x 261mm, so it needs a large-format printer (the 5mm brim adds 10mm each way). 🟩 𝗧𝗛𝗘 𝗡𝗨𝗠𝗕𝗘𝗥𝗦 ▸ Box: 319.3 x 260.5 x 120.65mm ▸ Handle: 307.3mm tall, 182.4mm wide ▸ Tall pockets: 82.55 x 137.16mm · Cleanser pocket: 79.4mm round · Aerosol pockets: 63.5mm round ▸ Parts: box, handle, pin Happy printing! 🔗