Christmas tree baubles
por TomasT en Printables
Multiple baubles to christmas tree (35 variants and sizes).
Licencia
Uso comercial permitidoPuedes imprimirlo, modificarlo y venderlo dando crédito al autor.
Al descargar aceptas respetar la licencia y dar crédito a TomasT.
Archivos (36)
- icicle-n150x.stl STL · 1,0 MB
- egg-110x.stl STL · 6,0 MB
- cone-140y_fixed.stl STL · 8,0 MB
- needle-140l.stl STL · 2,2 MB
- cone-120d_fixed.stl STL · 3,6 MB
- egg-080b.stl STL · 632 KB
- egg-110d.stl STL · 4,2 MB
- needle-140d.stl STL · 4,0 MB
- icicle-n100l.stl STL · 538 KB
- cone-140b_fixed.stl STL · 651 KB
- hedgehog-100.stl STL · 123 KB
- egg-080x.stl STL · 5,7 MB
- needle-140b_fixed.stl STL · 621 KB
- icicle-h150x.stl STL · 1,8 MB
- icicle-h100x.stl STL · 1,8 MB
- egg-080y.stl STL · 9,4 MB
- cone-120y_fixed.stl STL · 7,9 MB
- egg-080l.stl STL · 2,3 MB
- needle-140x_fixed.stl STL · 6,8 MB
- icicle-h100l.stl STL · 964 KB
- icicle-n100x.stl STL · 1,0 MB
- egg-110y.stl STL · 9,7 MB
- cone-120b_fixed.stl STL · 635 KB
- egg-080d.stl STL · 4,1 MB
- egg-110b_fixed.stl STL · 977 KB
- icicle-h150l.stl STL · 969 KB
- needle-140y.stl STL · 9,4 MB
- icicle-m100x.stl STL · 1,7 MB
- handle.stl STL · 93 KB
- cone-140x_fixed.stl STL · 7,0 MB
- cone-120l.stl STL · 2,3 MB
- egg-110l.stl STL · 2,3 MB
- icicle-n150l.stl STL · 541 KB
- cone-140l_fixed.stl STL · 2,9 MB
- cone-140d_fixed.stl STL · 3,6 MB
- cone-120x.stl STL · 5,7 MB
- Categoría
- Figuras y arte
- Formatos
- STL
- Descargas
- 5,389
- Publicado
Sobre este modelo
Multiple baubles to christmas tree (35 variants and sizes).
Prepared for printing in vase/spiral mode - I recommended minimal 0,4 or 0,5 nozzle and set extrusion line width more than 100%. In some parts of baubles (overhangs) i use layer height 0,1 or 0,15, othervise 0,2 mm.
Must be printed upside down and you must add larger brim/skirt (8-10mm width).
Very good looking from transparent ABS (clear and red on images), transparent PLA is usable too (green on images). PETG I not tested.
Top handle i printed from gold/silver PLA. All inserted baubles using identical size of handle.
If you will change X/Y size of any bauble, you must print handle in identical size.
EDIT: some original files had bad size of bottom cylinder - I repaired it and upload new versions (with _fixed in name)
Print instructions Category: Decor Print Settings
Printer Brand: Creality
Printer: Ender 2
Rafts: No
Supports: No
Resolution: 0,2 (somewhere 0,1 or 0,15)
Infill: no
Filament: Hobbyking, Gembird ABS, PLA clear, red, green, silver, gold
Descripción original del autor, publicada en Printables.
