Cable Dock + Clips | H3C Desk Collection

Stop chasing charging cables that slip off the desk. Press each cable down through a neck into its round channel: the plug stays at the front, ready to grab, and the cable runs out the back. A second plate has 10 small adhesive clips for routing cables under or along the desk. Why it is different - 5 channels for cables of 4, 5, 6, 5 and 4 mm. Each one has a narrower neck (78% of the cable diameter) with a chamfered entry, so the cable clicks in and stays.

- The plug can't pull through: the dock holds the cable end right at the front edge.

- 10 clips on plate 2 (two each for 3, 4, 5, 6 and 8 mm cables) with a 45 degree teardrop bore, so they print flat with no supports. Stick them on with double-sided tape.

- Three textures, one family: DUNE (sand ripples), HIVE (hexagons that shrink toward the rim) and NINE (architectural flutes). The same look as the H3C Purge Bin.

- NINE TOOLS badge: an engraved emblem with nine dots for the nine PrintTools. Print it in one colour, or as a flush 2-colour inlay on the H3C.

- Seamless wrap: every texture is tuned so the pattern closes perfectly around the back, with no seam line.

- Support-free and plate-ready: overhangs are 45 degrees or less (plus a few short bridges), and every profile slices with no warnings.

What's included - 3MF profiles for DUNE, HIVE and NINE: H3C 2 colours (inlay) and 1 colour all printers

- STL per texture (body + inlay), and the clips STL

Size - Dock: 106 x 48 x 38 mm

- Channels: 4 / 5 / 6 / 5 / 4 mm

- Clips: 14 mm long pads, 3 / 4 / 5 / 6 / 8 mm

- Weight: about 60 g dock + 9 g clips

How to use - Plate 1: dock, upright. Plate 2: clips. No supports.

- Press a cable into its channel from the top until it clicks.

- Clips: clean the surface, add a strip of double-sided tape under the pad and press for 10 seconds.

Print settings - Material: PLA (Bambu PLA Basic). 0.4 mm nozzle, 0.20 mm layers, 3 walls, 15% infill, Textured PEI plate.

- No supports. Seam on the back.

- 2 colours: the inlay is a separate part already assigned to filament 2. The time includes the prime tower.

- The all-printers profile is built on the Bambu Lab A1 mini (180 mm), so it opens on any Bambu printer and fits small beds.

Print profiles (sliced in Bambu Studio) - DUNE - 2 colours (NINE TOOLS inlay) - H3C - PLA: 1.32 h, 64 + 3 g + clips 9 g

- DUNE - 1 colour - all printers - PLA: 1.68 h, 60 g + clips 9 g

- HIVE - 2 colours (NINE TOOLS inlay) - H3C - PLA: 1.50 h, 64 + 3 g + clips 9 g

- HIVE - 1 colour - all printers - PLA: 1.90 h, 60 g + clips 9 g

- NINE - 2 colours (NINE TOOLS inlay) - H3C - PLA: 1.44 h, 64 + 3 g + clips 9 g

- NINE - 1 colour - all printers - PLA: 1.79 h, 60 g + clips 9 g

Files STLs in print orientation (Z up): <SKIN>_body.stl works alone as a 1-colour print with an engraved badge; <SKIN>_inlay.stl is the optional 2nd colour that fills the engraving. For 2 colours, load both together and answer Yes to 'load as a single object with multiple parts', then set the inlay to filament 2. Cable_Clips_x10.stl is the clip plate. The collection Part of the NINE TOOLS H3C Desk Collection: pen cup, desk bin, catch-all tray, cable dock + clips, phone stand, desk caddy and headphone stand, all in the same three textures. If this tidies up your desk, a Like or a Make with a photo really helps. Tell me which texture you printed! Gallery images are photorealistic renders made from these exact print files. Original design. Not affiliated with Bambu Lab.