Bird house
por Didier en Printables
Wanted a bird house easy to install which could have an organic feel. Made the base removable if ever we need to clean…
Licencia
Uso comercial permitidoPuedes imprimirlo, modificarlo y venderlo dando crédito al autor.
Al descargar aceptas respetar la licencia y dar crédito a Didier.
Archivos (11)
- Cabanne Bv2.3mf 3MF · 1,6 MB
- Cabanne Bv2 - Haut.3mf 3MF · 1,6 MB
- Cabanne Av2 - Haut.3mf 3MF · 2,6 MB
- Cabanne Av2 - Toit.3mf 3MF · 2,6 MB
- Cabanne_A5_-_Haut.stl STL · 8,0 MB
- Cabanne Bv2.obj OBJ · 10,0 MB
- Cabanne Av2 - HautNoRoof.obj OBJ · 13,0 MB
- Cabanne Bv2 - HautNoRoof.obj OBJ · 10,1 MB
- Cabanne_A4_-_Haut.stl STL · 3,0 MB
- Cabanne Av2 - Base -0.4mm - very tight not recommended.3mf 3MF · 417 KB
- Cabanne Av2 - Base -0.8mm.3mf 3MF · 418 KB
- Categoría
- Jardín
- Formatos
- 3MF, STL, OBJ
- Descargas
- 1,556
- Publicado
Sobre este modelo
Wanted a bird house easy to install which could have an organic feel. Made the base removable if ever we need to clean it. I had some fun playing with the spline to build various form and could not establish which one is the most interesting so I have uploaded a couple. That is build to not require any support. The hole is 30 mm to attract mostly small birds. The hole in the top is build to slide a cord into it. Technically the bases is the same for all design but just for simplicity I have uploaded one per. 2022-05-10 modified the design for the main one to incorporate feedbacks. - Added a slot in the bottom to add fixing the base to the top - Reduce friction by increasing the gap for the filet between the top and the base to 0.2 mm instead of 0.1 mm - Add bigger flat in the top hole to make it more robust and better seat washer if someone it that for fixing the rope - Added the small top over the hold to prevent rain from getting in the bird house.
2022-05-14 - Reduce the size of the base to simplify assembling pieces. - Also added a version B with a different form and single piece since adding the cord is not that hard so the removal base is not that useful- In that new design I added vent holes after reading more on bird house. - Also make it less wide to save on print time and material.
2023-07-29 - Created a new base with a bigger space to make it less fit one removing 1.1 mm and one 1.8 mm. - Exported in 3MF instead of OBJ - Exported both the version with and without the small wimsy roof
2024-02-23 - Exporting again the base since there might be an issue with the version. Each are to accomodate issue with printer tolerance. I used the -0.8 mm for my version. - The -0.4 should be the best fit but require the printer and materiel to not shrink to fit. - The -1.1 are -1.8 are removing 1.8 mm which are not recommended and you might end up gluing the piece. But if you print are shrinking a lot that could help
Print Settings Printer Brand: Prusa
Printer: Mk3 Rafts: No
Supports: No Resolution: 200 Infill: 38
Filament: PolyMaker PETG
Category: Outdoor & Garden
Descripción original del autor, publicada en Printables.
