Beltstrom CMP-60 - Deep Rock Galactic
por DRG_Prints en Printables
The Belstrom CMP-60 from Deep Rock Galactic: Rogue Core! Everything was modeled by me.
Licencia
Uso comercial permitidoPuedes imprimirlo, modificarlo y venderlo dando crédito al autor.
Al descargar aceptas respetar la licencia y dar crédito a DRG_Prints.
Archivos (31)
- Beltstrom CMP-60 - Trigger.stl STL · 1 KB
- Beltstrom CMP-60 - Release Button.stl STL · 2 KB
- Beltstrom CMP-60 - Back Square.stl STL · 3 KB
- Beltstrom CMP-60 - Underbarrel Thingy.stl STL · 4 KB
- Beltstrom CMP-60 - Back Screw.stl STL · 3 KB
- Beltstrom CMP-60 - Trigger Holder.stl STL · 1 KB
- Beltstrom CMP-60 - Barrel.stl STL · 4 KB
- Beltstrom CMP-60 - Top Magazine Guard.stl STL · 17 KB
- Beltstrom CMP-60 - Side Magazine Guard.stl STL · 12 KB
- Beltstrom CMP-60 - Front Sight.stl STL · 1 KB
- Beltstrom CMP-60 - Black Stripe.stl STL · 1 KB
- Beltstrom CMP-60 - Compensator.stl STL · 24 KB
- Beltstrom CMP-60 - Bulk Side Insert.stl STL · 4 KB
- Beltstrom CMP-60 - Side Rail.stl STL · 13 KB
- Beltstrom CMP-60 - Red Triangle.stl STL · 1 KB
- Beltstrom CMP-60 - Compensator Insert.stl STL · 6 KB
- Beltstrom CMP-60 - Rear Sight.stl STL · 1 KB
- Beltstrom CMP-60 - Front Magzine Guard.stl STL · 2 KB
- Beltstrom CMP-60 - Bulk.stl STL · 64 KB
- Beltstrom CMP-60 - Bulk Front.stl STL · 37 KB
- Beltstrom CMP-60 - Bulk Back.stl STL · 33 KB
- Beltstrom CMP-60 - Foregrip.stl STL · 19 KB
- Beltstrom CMP-60 - Side Rail Nub.stl STL · 2 KB
- Beltstrom CMP-60 - Back Grip (Right).stl STL · 312 KB
- Beltstrom CMP-60 - Rear Brown Grip.stl STL · 27 KB
- Beltstrom CMP-60 - Grip Screw.stl STL · 2 KB
- Beltstrom CMP-60 - Magazine.stl STL · 32 KB
- Beltstrom CMP-60 - Rear Green Grip.stl STL · 840 KB
- Beltstrom CMP-60 - Back Grip (Left).stl STL · 312 KB
- Beltstrom CMP-60 - Magazine Frojnt.stl STL · 12 KB
- Beltstrom CMP-60 - Magazine Back.stl STL · 24 KB
- Categoría
- Cosplay y props
- Formatos
- STL
- Descargas
- 2
- Publicado
Sobre este modelo
My take on the Beltstrom CMP-60 from Deep Rock Galactic: Rogue Core! The magazine is removable, so I'd recommend printing two. Some parts may require small amounts of superglue or a mallet to get them properly in place. Everything assembled just fine for me, but you may need to mess with the size for smaller parts in case they don't fit properly. Fitting the small red triangles are a particular annoyance. I also included a split version of both the magazine and the bulk in case your printer doesn't have enough space, since these pieces are rather long. Feel free to send me a message if you have any questions or problems! The gif below shows the proper assembly for the Beltstrom.
Descripción original del autor, publicada en Printables.
