Belt Hanger
por MakerX en MyMiniFactory
The "Finally, a Place for My Belts" Hanger 🎯
MyMiniFactory entrega los archivos a usuarios con cuenta gratuita
Licencia
Solo uso personalCC BY-NC-ND 4.0 — Atribución, no comercial, sin derivadas
Solo para uso personal, sin modificarlo y dando crédito. No se permite vender ni redistribuir cambios.
Al descargar aceptas respetar la licencia y dar crédito a MakerX.
Archivos (8)
- Makerx Belt Hanger V2 10Arms.stl STL
- Makerx Belt Hanger V2 12Arms.stl STL
- Makerx Belt Hanger V2 2Arms.stl STL
- Makerx Belt Hanger V2 4Arms.stl STL
- Makerx Belt Hanger V2 6Arms.stl STL
- Makerx Belt Hanger V2 8Arms.stl STL
- Makerx Belt Hanger.3Mf 3MF
- Makerx Belt Hanger.stl STL
- Categoría
- Moda y joyería
- Formatos
- STL, 3MF
- Descargas
- 7
- Publicado
Sobre este modelo
The "Finally, a Place for My Belts" Hanger 🎯
Every closet has that spot. The one where belts go to die — draped over a rod, coiled on a shelf, tangled with everything else. I wanted something clean, quick, and permanent. So I designed it myself.
🟩 𝗪𝗛𝗔𝗧 𝗠𝗔𝗞𝗘𝗦 𝗜𝗧 𝗪𝗢𝗥𝗞
▸ 𝗖𝗹𝗶𝗽𝘀 𝗥𝗶𝗴𝗵𝘁 𝘁𝗼 𝗬𝗼𝘂𝗿 𝗘𝘅𝗶𝘀𝘁𝗶𝗻𝗴 𝗥𝗼𝗱 — No screws, no hardware, no permanent closet modifications. Hangs just like any other hanger and stays put.
▸ 𝗠𝘂𝗹𝘁𝗶𝗽𝗹𝗲 𝗕𝗲𝗹𝘁𝘀, 𝗢𝗻𝗲 𝗛𝗮𝗻𝗴𝗲𝗿 — The open slot design keeps each belt separate, visible, and easy to grab on the way out the door.
▸ 𝗗𝗲𝘀𝗶𝗴𝗻𝗲𝗱 𝗶𝗻 𝗦𝗼𝗹𝗶𝗱𝗪𝗼𝗿𝗸𝘀, 𝗧𝗲𝘀𝘁𝗲𝗱 𝗶𝗻 𝘁𝗵𝗲 𝗪𝗶𝗹𝗱 — Not a remix, not a guess. Modeled from scratch, printed, and living in my own closet. Happy with both the quality and the durability after daily use.
▸ 𝗙𝗮𝘀𝘁 𝗣𝗿𝗶𝗻𝘁 — Simple geometry means this goes from bed to closet in no time.
🟩 𝗣𝗥𝗜𝗡𝗧 𝗦𝗘𝗧𝗧𝗜𝗡𝗚𝗦
No supports · 0.20mm layer height · 15% gyroid infill · 2 walls · PLA
Print it flat on the plate with a 5mm outer brim — that is what keeps the thin hook and the arm ends from lifting. About 59 minutes and 29g of filament.
Got a lot of belts? Print two. Happy hanging! 🎯
Descripción original del autor, publicada en MyMiniFactory.
