3D Printed Willys RC 4X4
por Marty Jaxx en MyMiniFactory
Hi ALL! I've had this uploaded here across multiple pages for a while now. I decided that its best to put everything under one page hence the re-upload.
MyMiniFactory entrega los archivos a usuarios con cuenta gratuita
Licencia
Solo uso personalMyMiniFactory - Credit - Remix - Noncommercial
Licencia de MyMiniFactory: puedes imprimirlo y remezclarlo dando crédito, sin fines comerciales.
Al descargar aceptas respetar la licencia y dar crédito a Marty Jaxx.
Archivos (115)
- A0100 Diff Housing X4Supports 1.Stl STL
- A0101 28Mm Axle Tube X2 1.Stl STL
- A0102 Axle End X2.Stl STL
- A0103 Left Steering Knuckle X1.Stl STL
- A0104 Right Steering Knuckle X1.Stl STL
- A0105 Pinion Housing X2Supports.stl STL
- A0106 Diff Cover X2Supports.stl STL
- A0107 Ring Gear X2.Stl STL
- A0108 Pinion Gear X2.Stl STL
- A0109 28Mm Rear Axle Tube X2.Stl STL
- A0110 Truss X2Optional.stl STL
- A0111 Wheel Spacer X4.Stl STL
- A0112 Wheel Retainer X4.Stl STL
- A0113 Outer Wheel.stl STL
- A0114 Inner Wheel.stl STL
- B0100 Front Tub Support.stl STL
- B0101 Rear Tub.stl STL
- B0102 Right Quarter Panel.stl STL
- B0103 Left Quarter Panel.stl STL
- B0104 Right Fender.stl STL
- B0105 Left Fender.stl STL
- B0106 Dash Support.stl STL
- B0107 Glove Box.stl STL
- B0108 Tailgate.stl STL
- B0109 Grill.stl STL
- B0110 Windshield Frame Support.stl STL
- B0111 Windshield Insert.stl STL
- B0112 Steering Column Holder.stl STL
- B0113 Willys Steering Wheel.stl STL
- B0114 Shifter Assembly.stl STL
- B0115 Handle Support.stl STL
- B0116 4 Spoke Steering Wheel.stl STL
- B0117 Seat X2.Stl STL
- B0118 Seat Mount X2.Stl STL
- B0119 Hood Hinge 1.Stl STL
- B0120 Hood Hinge 2.Stl STL
- B0121 Magnetic Hood Latch.stl STL
- B0122 Snorkle Hood.stl STL
- B0123 Hood.stl STL
- B0124 Snorkel Body.stl STL
- B0125 Snorkel Clamp.stl STL
- B0126 Snorkel Cap.stl STL
- D0100 Transmission Housing Top Support.stl STL
- D0101 Transmission Housing Bottom Supports.stl STL
- D0102 Flywheel Hex Adapter.stl STL
- D0105 Input Gear 1.Stl STL
- D0106 Input Gear 2.Stl STL
- D0107 Output Gear 1.Stl STL
- D0108 Output Gear 2.Stl STL
- D0109 Hex Shaft.stl STL
- D0110 Shift Plate.stl STL
- D0111 Spacer.stl STL
- D0112 Servo Bypass Low Gear.stl STL
- D0113 T Case Gear 1.Stl STL
- D0114 T Case Gear 2.Stl STL
- D0115 T Case Housing.stl STL
- D0116 T Case Cover.stl STL
- D0117 Rear Drive Shaft.stl STL
- D0118 Front Drive Shaft.stl STL
- E0100 Upper Crank Case.stl STL
- Categoría
- Varios
- Formatos
- STL
- Descargas
- 2,319
- Publicado
Sobre este modelo
Hi ALL! I've had this uploaded here across multiple pages for a while now. I decided that its best to put everything under one page hence the re-upload.
This project started after I got in contact with the creator of the Ossum Jeep and inquired about a fully printed version that did not rely on a donor RC vehicle. After learning that no plans to create such a version existed in the near future, a few ideas were exchanged, a new friendship was made and the urge to design what I had envisioned needed to be fulfilled.
This is a remixed version of the original Ossum Jeep and while it is dimensionally exact and shares a few components with the original, this is an entirely different beast that is designed from the ground up to be fully 3D printed, including the axles and entire drivetrain. It is a true 1:10 scale radio controlled 3D printed 4X4.
The Jeep uses parts that can be bought online or at the local hobby and hardware store. Links are provided on Instructables to various items on Amazon and AliExpress. This is designed to be an affordable 4X4 crawler that somebody can print and assemble from the ground up using basic hand tools and a little mechanical and electrical knowledge. It uses a Tamiya motor and gearbox that is cleverly hidden into a faux engine. The transmission is entirely printed with the exception of a carbon fiber shaft and some bearings. The axles are also designed to use common items like carbon fiber tubing and some 1/8" square shaft also known as key stock.
I really hope you guys enjoy the build. Let me know if you have any issues or if there are stl files missing.
Instructions: http://www.instructables.com/id/3D-Printed-Willys-RC-4X4/
Feel free to help me out on Patreon. These types of projects cost a lot to design, print and test. All funds go to R&D of future projects I have planned: https://www.patreon.com/MartyJaxx
Please visit 3D Anarchy as well as the Ossum Group on Facebook: https://www.facebook.com/groups/1358672314201686/ https://www.facebook.com/groups/1883252011928341/
Descripción original del autor, publicada en MyMiniFactory.
