3D Printable DJI Inspire V1.5
por ChrisKrieg en Thingiverse
Want a DJI Inspire One but don't want to spend $3K? Then this is the 3D printing project for you! The cost of building the frame and landing gear is only around $100. Add your electronics and get in the air for far less than DJI would charge. This is my project that evolved from the idea...
Licencia
Solo uso personalCC BY-NC 4.0 — Atribución, no comercial
Puedes imprimirlo y modificarlo para uso personal dando crédito. No se permite vender las impresiones.
Al descargar aceptas respetar la licencia y dar crédito a ChrisKrieg.
Archivos (47)
- Boom_Lift_Linkage_Sweep_1.stl STL · 40 KB
- Boom_Lift_Linkage_Sweep_2.stl STL · 39 KB
- Boom_Joint_20Deg_L.stl STL · 1,3 MB
- Boom_Joint_20Deg_R.stl STL · 1,3 MB
- Boom_Outer_Joint_1.stl STL · 449 KB
- Boom_Outer_Joint_2_20Deg_L.stl STL · 1,6 MB
- Boom_Outer_Joint_2_20Deg_R.stl STL · 1,6 MB
- Boom_Rod_Linkage_20Deg_L.stl STL · 17 KB
- Boom_Rod_Linkage_20Deg_R.stl STL · 17 KB
- Boom_Stop_Ring_V3_2pc.stl STL · 83 KB
- Boom_Support_Linkage_V4_2pc.stl STL · 65 KB
- Canopy_Nose_FPV_V1.5.stl STL · 457 KB
- Canopy_Tail_V1.5.stl STL · 162 KB
- Canopy_Top_V1.5_Split_A.stl STL · 474 KB
- Canopy_Top_V1.5_Split_B.stl STL · 127 KB
- Clamp_Angle_Guide.stl STL · 23 KB
- Drill_Guide_for_Wood_Screw.stl STL · 16 KB
- Drill_Guide_V1.5.stl STL · 377 KB
- Frame_38mm_Strut.stl STL · 63 KB
- Frame_Base_Plate_90mm_V1.5.stl STL · 322 KB
- Frame_Bushing_Holder_Front_V1.5.stl STL · 503 KB
- Frame_Bushing_Holder_Rear_V1.5.stl STL · 600 KB
- Frame_Bottom_V1.5.stl STL · 351 KB
- Frame_Joint_Bushing_V1.5.stl STL · 20 KB
- Frame_Motor_ESC_Box_RC-CAM.stl STL · 114 KB
- Frame_Motor_Foot_1_V1.5.stl STL · 556 KB
- Frame_Motor_Foot_2_V1.5.stl STL · 583 KB
- Frame_Motor_Mount_V1.5.stl STL · 468 KB
- Frame_Receiver_Shelf_90mm_V1.5.stl STL · 442 KB
- Frame_Strengthener_V1.5.stl STL · 57 KB
- Frame_Top_V1.5.stl STL · 433 KB
- Gimbal_Frame_V1.5.stl STL · 130 KB
- Gimbal_Plate_Diam_40mm_X.stl STL · 159 KB
- LED_Clip_V2.stl STL · 218 KB
- Servo_Cap_M5.stl STL · 43 KB
- Servo_Cap_M8.stl STL · 74 KB
- Wormdrive_Endstops_V1.5_for_M5_Nut.stl STL · 105 KB
- Wormdrive_Endstops_V1.5_for_M8_Nut.stl STL · 106 KB
- Wormdrive_Endstops_V1.5_for_Quarter-20_Nut.stl STL · 105 KB
- Wormdrive_Endstops_V1.5_M8Octo.stl STL · 110 KB
- Wormdrive_Endstops_V1.5_M8Round.stl STL · 155 KB
- Wormdrive_V1.5_for_M5_Nut.stl STL · 56 KB
- Wormdrive_V1.5_for_M8_Nut.stl STL · 58 KB
- Wormdrive_V1.5_M8Octo.stl STL · 62 KB
- Wormdrive_V1.5_M8Round.stl STL · 107 KB
- Wormdrive_V1.5_for_Quarter-20_Nut.stl STL · 57 KB
- ASM_Inspire_V1.5.stp STP · 7,2 MB
- Categoría
- Repuestos
- Formatos
- STL, STP
- Descargas
- 54,220
- Publicado
Sobre este modelo
Want a DJI Inspire One but don't want to spend $3K? Then this is the 3D printing project for you! The cost of building the frame and landing gear is only around $100. Add your electronics and get in the air for far less than DJI would charge. This is my project that evolved from the idea RCHobbiesUK developed. The RCGroups community took off from their inspiration and mutated their design into an entirely new beast that has considerable improvements. The full list of options, print settings, print checklist, hardware, electronics, wiring, and everything else can be read in full at the RCGroups thread http://www.rcgroups.com/forums/showthread.php?t=2399740#post31442294 The complete set of modeling files is on that page as well! So if you want to put your own twist on my design you won;t need to start from scratch.
Descripción original del autor, publicada en Thingiverse.
